AE Techron 3110 Standards Waveform Generator
- Includes a large library of Automotive and Aviation Standards’ test routines--complete list available as Supplemental Document under Datasheet on left
- Drag and drop interface makes it easy to modify existing tests or build new waveform sequences
- Loop entire tests or test sections; repeat loops with increments of up to four variables
AE Techron 3110A Standards Waveform Generator
- Easiest-to-use LF wave sequence generator
- 1550+ automotive and aviation standards' tests included
- Dramatically reduces test time for repetitive test sequences
AE Techron 7224 Power Amplifier | DC - 300kHz, 900VA
- Frequency bandwidth of DC to 300 kHz at rated power.
- Continuous output of over 1,100 watts RMS at 4 ohms.
- 40 mSec pulses of up to 52 amperes peak into a 0.5 ohm load.
AE Techron 7228 Linear Power Amplifier | 1000 W, 100kHz - 1MHz
- Up to 4X the long-term power of the 7224 at frequencies above 100 kHz
- Changes to protection, connection type and modes of operation are accomplished quickly by changing back-panel DIP switches or via remote contact closure
- Provides user-selectable current limit, DC Blocking and DC Servo for transformer-based loads
AE Techron 7234 Audio Power Amplifier
- Bench-sized
- Single-phase
- Drop outs and surges as fast as 1.2µs
AE Techron 8302 RF Amplifier
- Part of the 8300 Series
- Revolutionary switch-mode design
- Wide bandwidth and flexible
Amplifier Research CI00250A RF Conducted Immunity System
Amplifier Research CI00400A RF Conducted Immunity System
Amplifier Research CI00402 RF Conducted Immunity System
- Fully self-contained state of the art system designed to test RF conducted immunity
- The system contains a signal generator a spectrum analyzer a 100W nominal AR amplifier a 10 kHz to 400 MHz directional coupler emcware® control software
- a signal generator
AE Techron DSR 100-200 | Pulse 2B and 4
- 4-Quadrant – Can source and sink current.
- ±80V – DC supply for 12V to 48V systems; meets 80V surge requirements.
- 300 kHz Sine – DC ripple tests for all major standards.
Amplifier Research MT06000 Multistar Multi-tone RF Radiated Immunity System 80 MHz - 6 GHz
AE Techron T1000 Magnetic-Field Susceptibility Transformer
- Up to 100ARMS secondary current.
- Exceeds AF Magnetic Field test requirements of DO 160 Section 19 and Boeing D6-16050-5 Section 7.2.2.
- Circuit breaker protected from over-current.
AE Techron T2000 Low-Frequency Conducted Susceptibility Transformer
- Frequency response: 10 Hz to 250 kHz.
- Turns ratio: 2:1 step down
- Audio power: 200W
AE Techron T3700 Electric-Field Susceptibility Transformer
- Up to 3,700 volts, 11,000 V/m.
- Meets or exceeds voltage requirements of DO 160 Section 19 and Boeing D6-16050-5 Section 7.2.
- Robust design; withstand tested to 5,000VRMS.
BOLAB 100-TS Series | DC – 200 kHz, 400 W – 18000 W
- DC to 200 kHz full range bandwidth
- Rise time / fall time up to 100 V/µs
- Arbitrary function with 1 Million memory data points
Pearson Electronics 101 Current Monitor Probe | 0.25Hz - 4MHz
Pearson Electronics 110 Current Monitor Probe | 1Hz – 20MHz
- Current monitor probe
- Robust peak current capacity of 5 kA
- Frequency response reaching up to 20 MHz
PMM 150-50-BCL Ohm Adapter
- 3 watts power rating
- Conducted immunity system testing
- Frequency range of 10 kHz to 230 MHz
Solar 2352-1 Audio Power Amplifier, 15 Hz - 150 KHz
Pearson Electronics 3525 Current Monitor | 5 Hz – 15 MHz
- 0.1 V/A +1/-0% sensitivity
- 50 Ω output resistance
- Maximum peak current of 5000 A
Teseq NSG 4070B
- Integrated signal generator 9 kHz – 1 GHz
- 3 power meter inputs 9 kHz – 1 GHz
- Integrated class A power amplifier module for different applications: 35 W, 150 kHz – 230 MHz; 40 W, 10 kHz – 400 MHz 45 W, 9 kHz – 1 GHz; 80 W, 150 kHz
Solar 7541-1 Spike Receptor Probe
- Spike receptor probe (calibrated for use with oscilloscope)
- The receptor probe is assembled with a hinged construction
- Includes a calibrating resistor mounted in the housing
Solar 9108-1N Clamp-On Injection Probe | 10 KHz – 200 MHz
- Bulk current injection probe
- Frequency range of 10 kHz and 200 MHz
- 1.25-inch diameter window
Solar 9120-1N Injection Probe
- Injection probe
- Split toroidal design for easy clamping onto test wires
- Calibrated for insertion loss and transfer impedance
Solar 9123-1 Current Monitor Probe | 10 kHz – 500 MHz
- Bulk current injection probe for EMI testing
- Clamp-on design
- Frequency range of 10 kHz to 500 MHz
Solar 9142-1N Bulk Current Injection Probe | 2 MHz – 450 MHz
- Bulk current injection probe
- Frequency range of 2 MHz to 450 MHz
- Maximum input power of 200 W
Solar 9144-1N Injection Probe
- Injection probe
- Unique split toroidal structure
- Designed to maintain a low voltage standing wave ratio
Solar 9335-2 Multiple Impedance Coupling Device
ETS-Lindgren 95236-1 Bulk Current Injection Probe
Solar 9719-1N Injection Probe
- Bulk current injection probe
- Has a frequency range of 10 kHz to 350 MHz
- Designed for continuous 30-minute use at full power
BOLAB AN-ABCD-300-C10 Artificial Network System | 1000 V, 300 A
- In accordance with LV123, ISO 21498, MBN 11123, VW 80300, and IEC 61851-23
- Liquid cooled for stabile resistance temperature and constant ohmic value
- True continues current loading without derating, ideal for in-the-loop testing during the development stage of HV components
Bolab AN-ABCD-60 Artificial Network System | 1000 V, 60 A
- In accordance with LV123, ISO 21498, MBN 11123, VW 80300, and IEC 61851-23
- Liquid cooled for stable resistance temperature and constant ohmic value
- True continues current loading without derating, ideal for in-the-loop testing during the development stage of HV components
Fischer Custom Communications BCICF-1 Calibration Fixture
- Excellent VSWR over a broad bandwidth: <2:1 over the frequency range of 10kHz – 400 MHz when the probe is in fixture
- Accommodates a wide variety of Bulk Current Injection Probes that operate between 10 kHz – 400 MHz
Fischer Custom Communications FCC-BCICF-2
- Bulk current injection probe fixture
- Matched with the F-140 bulk current injection probe
- Easy-to-use design
AH Systems BCP-510 Broadband Current Probe | 20Hz - 1MHz
- Measures currents on 50 Hz, 60 Hz and 400 Hz powerlines
- Individually Calibrated (Transfer Impedance calibration included)
- Split Type Clamp-on Design
AH Systems BCP-511 Broadband Current Probe | 20 kHz – 100 MHz
- Measure conducted emissions from 20 kHz to 100 MHz
- Capable of measuring pulse currents up to 100 amperes with a duty cycle of 0.001
- Individually calibrated (transfer impedance calibration included)
AH Systems BCP-512 Broadband Current Probe | 1MHz - 1000MHz
- Individually Calibrated (Transfer Impedance calibration included)
- High Current Capability
- Split Type Clamp-on Design
AH Systems BCP-520 Broadband Current | 10kHz - 500MHz
- Individually Calibrated (Transfer Impedance calibration included)
- High current conducted emissions measurements without saturation
- High Current Capability
AH Systems BCP-526 Broadband Current Probe | 100kHz - 1GHz
- High current conducted emissions measurements without saturation.
- Individually Calibrated (Transfer Impedance calibration included)
- High Current Capability
AH Systems BCP 600 Series | 20 Hz – 500 MHz
- A variety of current probe configurations
- Frequencies ranging from 20 Hz to 500 MHz
- Lightweight designs
BOLAB Systems BLS-130-70N-TS 4-Quadrant Voltage Amplifier
- DC to 200 kHz full range bandwidth
- DC up to 1 MHz (small signal -3 dB)
- Option for running as a current amplifier
Schloder CDG7000 Conducted Disturbances Test System
- Compact device
- Consists of an RF signal generator, an RF-power amplifier, a 3-channel RF voltmeter, and a directional coupler
- RF power amplifier is available in three different models
Com-Power CDN-AF2 Coupling/Decoupling Network (CDN)
PMM CDN-AF2 Coupling Decoupling Network
- 150 kHz - 230 MHz
- 4 mm Safety Lab Connectors
- 250 V AC / 250 V DC
Schwarzbeck CDN-AF2
- Part of the coupling decoupling network series
- For conducted common mode immunity testing according to IEC 61000-4-6
- Frequency range of 0.15 - 230 MHz
Com-Power CDN-AF4 Coupling/Decoupling Network (CDN)
Schwarzbeck CDN-AF4
- Part of the coupling decoupling network series
- For conducted common mode immunity testing
- Intended to inject common mode disturbance signals to control lines
Com-Power CDN-AF8 Coupling/Decoupling Network (CDN)
Com-Power CDN-C75 Coupling/Decoupling Network (CDN)
Com-Power CDN-M125E Couplers Coaxial
- Frequency Range - 150 kHz -230 MHz
- Meets EN 61000-4-6 requirements
- Current Rating: up to 25 Amps
EM Test CDN-M2/M3N for Supply Lines
- For 2 or 3 AC/DC supply lines (switchable)
- AE: IEC 320 connector
- EUT: 4mm safety lab connectors
Schwarzbeck CDN M2/M3PE-16A
- Part of Schwarzbeck's coupling decoupling network series
- For conducted common mode immunity testing according to IEC 61000-4-6
- Immunity testing on unscreened AC and DC power supply lines (mains lines)
Com-Power CDN-M225E Coupling/Decoupling Network (CDN)
- Frequency Range - 150 kHz - 230 MHz
- Meets EN 61000-4-6 requirements
- Current Rating: 25 Amps
Com-Power CDN-M325 Coupling/Decoupling Network (CDN)
Schwarzbeck CDN-M4-63A-1000V
- Part of the coupling decoupling network series
- For conducted common mode immunity testing
- Suitable for immunity testing on unscreened AC and DC power supply lines
Com-Power CDN-M425 Coupling/Decoupling Network (CDN)
- Frequency Range - 150 kHz - 80 MHz
- Meets EN 61000-4-6 requirements
- Current Rating: up to 25 Amps
Schwarzbeck CDN M4PE-32A-1000V
- Intended to inject common mode disturbance signals to power supply or mains lines
- Frequency range of 150 kHz to 230 MHz
- Complies with the requirements of IEC 61000-4-6
Com-Power CDN-M525 Coupling/Decoupling Network (CDN)
Com-Power CDN-M525E Five Conductor Power Line 25 Amp CDN
- Product Name: Coupling Decoupling Network (CDN)
- Compliant Test Standards: IEC / EN 61000-4-6
- Application: Five conductor power cable
Schwarzbeck CDN-M5PE 125A 1000V
- Sufficient decoupling between Auxiliary Equipment (AE) and disturbance signal
- Available for a multitude of cable types and connectors
- In compliance to IEC 61000-4-6
_24.jpg)
Schwarzbeck CDN-M5PE-32A-1000V
- Part of the coupling decoupling network series
- For conducted common mode immunity testing according to IEC 61000-4-6
- Frequency range of 150 kHz to 230 MHz
_24.jpg)
Schwarzbeck CDN M5PE 63A 1000V
- Part of the coupling decoupling network series
- For conducted common mode immunity testing, according to IEC 61000-4-6
- Frequency range of 150 kHz - 230 MHz
Com-Power CDN-S1 Coupling/Decoupling Network (CDN)
- For Signal Lines
- Frequency Range - 150 kHz - 80 MHz
- Meets EN 61000-4-6 Requirements
Com-Power CDN-S2 2 Wire Coupling/Decoupling Network (CDN)
- For Signal Lines
- Frequency Range - 150 kHz - 80 MHz
- Meets EN 61000-4-6 Requirements
Schwarzbeck CDN-S25-SUBD
- Part of the coupling decoupling network series
- For conducted common mode immunity testing according to IEC 61000-4-6
- Frequency range of 10 kHz to 230 MHz
Com-Power CDN-S4 4 Wire Coupling/Decoupling Networks (CDN)
Com-Power CDN-T2 Coupling/Decoupling Network (CDN)
- For Signal Lines
- Frequency Range - 150 kHz - 80 MHz
- Meets EN 61000-4-6 Requirements
Com-Power CDN-T4 Coupling/Decoupling Network (CDN)
Schwarzbeck CDN-T4-RJ45
- Part of the coupling decoupling network series
- Frequency range of 10 kHz to 230 MHz
- For conducted common mode immunity testing
Schwarzbeck CDN-T8-RJ45
- Part of the coupling decoupling network series
- For conducted common mode immunity testing according to IEC 61000-4-6
- Frequency range of 10 kHz to 230 MHz
Com-Power CDN-T8E CDN for 8 Line (4 Balanced Pairs)
- Frequency range of 150 kHz to 230 MHz
- Designed for IEC / EN 61000-4-6
- Four unscreened, balanced pairs
Com-Power CDN-USB-AE Coupling Decoupling Network
- Frequency range 150 MHz-230 MHz
- Meets CISPR 16-1-2 requirements
- USB cables with type A connector
Teseq CDN USB/P Coupling/Decoupling Network
- Designed for IEC/EN 61000-4-6
- USB/p for test peripheral devices
Frankonia CIT-10 Compact Immunity Test System, 10 kHz - 400 MHz
- Conducted RF immunity tests acc. to IEC/EN 61000-4-6 and BCI tests acc. to ISO 11452-4 and MIL–STD 461E
- Signal generator, RF-power amplifier, RF-power meter and directional coupler (optional) in one 19”-case
- Stand-alone operation possible with optional available netbook
Frankonia CIT-1000 Conducted Immunity Test System
- Conducted RF immunity tests acc. to IEC/EN 61000-4-6, BCI-tests acc. to ISO 11452-4 and MIL-STD 46
- Signal generator, RF-Power-Amplifier, 3-channel power-meter and directional coupler combined in one 19“ case.
- Stand-alone operation via integrated touchscreen PC
PMM CLA-050 Absorbing Clamp 30 MHz - 1 GHz
- Frequency range 30 MHz to 1 GHz
- Useful for disturbance power measurement & screening attenuation of cables
- Complies with CISPR 16-1-3
Com-Power CLA-150 Absorbing Clamp 30 MHz - 1 GHz
- Frequency Range: 30 - 1000 MHz
- Impedance: 50 Ohm
- Connector Type: BNC (f)
Com-Power CLCE-1032 RF Current Probe | 9 kHz – 1000 MHz
- Frequency range of 9 kHz to 1000 MHz
- Suitable for CISPR, MIL-STD-461, and DO-160
- Individual calibration
Com-Power CLCE-332 RF Current Probe | 9 kHz – 300 MHz
- Frequency range of 9 kHz to 300 MHz
- Suitable for CISPR, MIL-STD-461, and DO-160
- Individual calibration
PMM CLCE-400 Current Monitor Probe | 10 kHz – 400 MHz
- Frequency Range: 10 kHz to 400 MHz
- Suitable for CISPR, Mil-STD-461 & DO-160
Com-Power CLCE-438 RF Current Probe | 9 kHz – 400 MHz
- Frequency range of 9 kHz to 400 MHz
- Suitable for CISPR, MIL-STD-461, and DO-160
- Individual calibration
Teseq CN Series Coupling Network (CN) For IEC / EN 61000-4-16, DC to 150 kHz
- M4, 100 A, 690VAC
- Coupling networks designed for IEC / EN 61000-4-16
- M series for DC or AC power ports A series for communication ports, intended for unscreened, unbalanced lines
EMC Partner CN16T8 DC Coupling-Decoupling Network
- DC Line CDN for 8 Lines (4 pairs)
- ​EUT / AE connector (RJ45)
- IEC 61000-4-16 standard
PMM Cond-IS/10 Conducted Immunity System
- Generator 3010, 9 kHz – 1 GHz, -107 to +10 dBm
- Amplifier 6000N, 9 kHz – 230 MHz, 10/15 W
- ATT-25W, 6 dB Attenuator, 25 W max
PMM Cond-IS/10-CIP Conducted Immunity System
- Generator 3010, 9 kHz – 1 GHz, -107 to +10 dBm
- Amplifier 6000N, 9 kHz – 230 MHz, 10/15 W
- ATT-25W, 6 dB Attenuator, 25 W max
LeCroy CP150 Current Probe
- Current probe
- Compact design
- Broad bandwidth
Teseq CT 419-5 Current Transformer for IEC / EN 61000-4-19
- Coupling transformer designed for IEC/EN 61000-4-19
- Frequency range 2 kHz to 150 kHz
- 4 mm banana sockets
EM Test CWS 500N2 Continuous Wave Simulator
- Supports BCI testing as per various standard requirements
- Basic frequency range 9kHz up to 400MHz
- Extendable frequency range up to 1GHz
EM Test CWS 500N3 Low Frequency Simulator 10 Hz - 250 kHz
EM Test CWS 500N4 Conducted/Common-mode Disturbance Simulator, DC - 165 kHz
- Most compact equipment for common-mode disturbances as per IEC 61000-4-16
- Built-in LF signal generator and LF amplifier
- Sweep mode capability 10Hz to 165kHz
EM Test CWS 500N1 Continuous Wave Simulator, 80W
- Signal generator 9kHz to 1GHz
- Amplitude modulation: 1Hz to 3kHz (0% to 95%)
- Pulse modulation: 1Hz - 1kHz (10% to 90%)
PMM EMCL-20 10 kHz - 1GHz EM Injection Clamp | 20mm Aperture
- EM clamp for immunity testing of cables with up to 20 (35) mm diameter
- High coupling factor: less than 15 watts amplifier output power is required to obtain a test level of 10 V
- Calibration unit and calibration data are supplied with each instrument
PMM EMCL-35 10 kHz - 1 GHz EM Injection Clamp | 35mm Aperture
- EM clamp for immunity testing of cables with up to 20 (35) mm diameter
- High coupling factor: less than 15 watts amplifier output power is required to obtain a test level of 10 V
- Calibration unit and calibration data are supplied with each instrument
Fischer Custom Communications F-120-9A
- 7 dB attenuation between 100 kHz and 230 MHz when measured into a 50 ohms fixture
- Perform IEC 1000-4-6 testing with 20 watts or less of RF power
- Usable up to 200 watts
Fischer Custom Communications F-120615-1006-1 EM Injection Clamp
Fischer Custom Communications F-130A Bulk Current Injector Probe
- Broad band high efficiency injection probe
- Frequency range of 1 MHz to 700 MHz
- Insertion loss of 6 dB or less
Fischer Custom Communications F-16-1 Current Probe | 10Hz - 70MHz
Fischer Custom Communications F-203I-A-23mm EM Injection Clamp
Fischer Custom Communications F-203I-A-32mm EM Injection Clamp
Fischer Custom Communications F-33-2 Current Probe | 1kHz - 250MHz
- Compact probes with an external diameter of roughly 71 mm and an internal diameter of 32 mm
- Frequency spectrum from 1 kHz to 250 MHz
- BNC connector
Fischer Custom Communications F-72 Current Probe | 100Hz - 100MHz
AH Systems ICP-621 Injection Current Probe | 10 kHz – 100 MHz
- Broad frequency range of 10 kHz to 100 MHz
- Individually calibrated
- Split type clamp-on design
AH Systems ICP-622 Injection Current Probe | 1 MHz – 500 MHz
- Broad frequency range of 1 MHz to 500 MHz
- Individually calibrated
- Split type clamp-on design
EMC Partner IMU C-SHORT Common Mode Short Duration Testing Extension
- IEC 61000-4-16 Standard
- Testing capabilities that find conducted immunity
- Common mode extension
EMC Partner IMU-MGS C Common Mode Extension
- IEC 61000-4-16 latest edition standard
- Frequency range of 0 Hz to 150 kHz
- Adjustable sweep time
EMC Partner IMU Slave Smart I1V1 External Module
- Voltage and current tests possible with one unit
- Exceeds maximum test levels in IEC 61000-4-19
- Integrated current source up to 25A
_17.png)
Prâna IP-DR250 Bulk Current Injection Probe
- Broadband (instantaneous single band) : 10 kHz – 400 MHz
- Frequency extension between 4kHz to 10kHz possible with limited power specifications
- Typical power: 500 W CW
Teseq ITS 6006 Radiated Immunity Test System 80 MHz - 6 GHz
- Integrated signal generator 80 MHz to 6 GHz
- Integrated RF switch network
- Multiple EUT monitoring options
Teseq (Schaffner) KEMA 801A Decoupling Clamp
- Decoupling Network/ RF attenuation clamp
- As specified in IEC/EN 61000-4-6
- Very efficient coupling
Teseq KEMZ 801AS 10 kHz - 1 GHz EM Clamp for IEC/EC 61000-4-6
- As specified in IEC/EN 61000-4-6
- Very efficient coupling
- Can be used on almost any cable
Teseq CDND M316-2 Coupling/Decoupling Network for Differential Mode
- Coupling networks designed for voltage test IEC/EN 61000-4-19
- Frequency range 2 kHz to 150 kHz
- 4 mm banana sockets
Teseq Mil-Std-461 CS114 10kHz - 400 MHz Conducted Susceptibility Test System
- Signal generation: NSG 4070-0
- Modulator: included in NSG 4070-0
- Power meter: 3x included in NSG 4070-0
Frankonia MTS-800 Magnetic-Field Low-Frequency Emission and Immunity Test System
- Frequency range for emission and immunity measurements: DC – 250 kHz
- 800W precision power amplifier, signal generator and spectrum analyzer in one compact unit
- All instruments may as well be used as stand-alone devices
Teseq NSG 4060 Low Frequency Immunity Test System
- Signal generator and integrated power amplifier 15 Hz to 150 kHz
- Meets IEC / EN 61000-4-16 in combination with the Extension Unit
- Meets IEC / EN 61000-4-19 and other standards
Teseq NSG 4070C Test System for Conducted and Radiated Immunity
- Class A power amplifier module can be integrated for different applications:
- 35 W, 150 kHz to 230 MHz;
- 40 W, 10 kHz to 400 MHz;
Teseq NSG 4070C-110 Test System for Conducted and Radiated Immunity
- IEC/EN 61000-4-6
- 110W, 10kHz - 400MHz amplifier
- 4kHz - 1 GHz signal generator
Teseq NSG 4070C-80 Test System for Conducted and Radiated Immunity
- IEC/EN 61000-4-6
- 110W, 150kHz - 230MHz amplifier
- 4kHz - 1 GHz signal generator / power meter
Teseq NSG2070, IEC 61000-4-6 Test System, 100 kHz - 250 MHz
Teseq NSG 4070-75 Conducted & Radiated Immunity Test System
- Integrated signal generator 9kHz to 1GHz
- 4-channel power meter 9kHz to 1GHzAn advanced combination of signal generator and compact immunity test system.
- Integrated power amplifier module for different
PMM BCICF-4 Injection Probe Calibration Fixtures
PMM BCICF-6-150 Injection Probe Calibration Fixtures
PMM F-120-9A Injection Probe
PMM RAD-IS/3G-600 Radiated Immunity System
PMM RAD-IS/3G-600 Radiated Immunity System Series
PMM RAD-IS/3G-601 Radiated Immunity System
PMM RAD-IS/3G-602 Radiated Immunity System
Tektronix TCP0020 Current Probe
- Easy-to-use design
- DC to >50 MHz bandwidth
- Core jaw diameter of 5 mm (0.2 in)
Tektronix TCP303
- Easy Current Measurements
- Probe Connects Directly to TDS Scope through TEKPROBE™ BNC Interface
- Split Core Construction for Easy Circuit Connection
Tektronix TCPA300 Current Probe Amplifier
- DC to 100 MHz maximum bandwidth
- Automatic control and onscreen scaling and units
- AC/DC input coupling