Megger HT1000/2 Copper Wire Analyzer

The Megger HT1000/2 Copper Wire Analyzer is a high performance, full feature, hand held instrument designed to provide copper wire provisioning and maintenance technicians with the most critical tests at the touch of a button. Durable and water resistant, the HT1000/2 is equipped with a highly effective 1/4 VGA LCD screen and a powerful backlight designed to make testing and troubleshooting easier in all work environments.

Product Info Related Products

ACV: 0 V to 250 V (±2%, ± 1 V)
DCV: 0 V to ±300 V (±2%, ±1 V)
Resistance: 0 Ω to 1,000 KΩ (±2%, ±1 Ω)
Leakage: 1 MΩ to 999 MΩ (±3%), 150 V open circuit output
Longitudinal balance: +30 dBrn to +80 dBrn (±2 dBrn)
Super Stress™: -10 dBrn to +30 dBrn (±2 dBrn)
Load coil detection: 0 coil to 4 coils (±1 coil)
Loop current: 0 mA to ±100 mA (±2%, ±1 mA)
Power influence: +40 dBrnC to +100 dBrnC (±2 dBrnC)
Noise (Voice Band): 0 dBrnC to +60 dBrnC (±2 dBrnC)
Loss (Voice Band): -40 dBm to +10 dBm (±1 dBm)

Noise finder via a 30 MHz spectrum analyzer
7 user selectable auto tests
Incremental pair test program
200 pair pre-post test storage
AC or DC power
USB port downloads updates and uploads test results

SKU: MEGG-HT1000/2

Megger EZ-Restore Cable Fault Locator

Has back-feed alert
Weighs less than 48.5 lbs
Offers unique USB load

3M Dynatel 2573-iD Cable/Pipe/Fault and Marker Locator

Trace view mapping display mode
6 active frequencies for direct connect
4 induction frequencies with maximum allowed output power

Dynatel 505 Portable Cable and Conductor Identifier

High Voltage Inc. CDS-2010U Cable Fault Locator

Combination Hipot, Burner and Fault Locator
Constant energy at each output voltage setting
Adjustable thump (impulse) repetition rate, from 6 – 10 seconds

Megger PFL32M1500-EN Portable Cable Fault Location System

Portable, rugged fault locating systems
HV insulation testing to 20 kV
Proof/burn up to 20 kV, 115 mA

Dynatel 1420-iD Electronic Marker System Locator

Large backlit, high-resolution graphic display
Locator PC tools software
PC interface via standard RS232/USB

Dynatel 2250M Cable/Fault Locater System

A easy-to-use system that requires very little operator training
Trace a pipe or cable and locate markers along the way
M-iD versions locate and read/write to all EMS-RFiD markers

Hipotronics CF30-8-A Cable Fault Locator / Thumper

Self-Contained Unit Features Proof Tester, Burner and Thumper in One
Burn Currents to 50 mA
Impulse Energies of up to 900 J

MOHR CT100B TDR Cable Analyzer

Rugged portable TDR with S‐parameter tools
Resolves connector detail ( <1 cm)
75 µm (0.003 in.) cursor resolution

Megger CFL535G Advanced Dual Channel TDR

Comprehensive Dual Channel capability with dual aspect display.
AUTO set up mode for instant use.
Ultra fast pulse for near end fault identification.

Amprobe AT 5005 Underground Cable / Pipe Locator System

Locates underground energized and de-energized wires, cables and pipes, eliminates exploratory digging in parking lots or under floors for buried pipes and wires
Signal Select and Distortion Alert icon indicates clean signal of the traced line, versus "ghost" and "return" path signals coming from the neighboring lines
Three testing modes for best accuracy: Passive Power Mode (50, 60, 100 and 120 Hz) – tracing energized lines conducting current Passive Radio Mode (RF) – using surrounding radio