AEMC PowerPad IV Model 8345 Power Quality Analyzer
- Full compliance with IEC 61000-4-30 ed. 3.0 Class A functions
- Real-time display of color waveforms (5 voltage/4 current) from 1 cycle to 10/12 cycles
- Calculation of unbalance (current and voltage)
Dranetz HDPQ Xplorer 400 Power Quality Analyzer
- 50/60Hz and 400Hz operating modes
- 1000Vrms, AC/DC, 512 samples/cycle
- 10 to 2000Vpk
Dranetz HDPQ Xplorer Power Quality Analyzer
- High definition PQ & energy monitoring: 1000 Vrms, AC / DC, 512 samples/cycle
- High speed digitized transients to 1us – to 2000Vpk
- Eight channels, 4 voltage & 4 current
AEMC 8335 PowerPad Three-Phase Power Quality Analyzer
- Measurement of TRMS voltages up to 1000Vrms AC/DC for two, three, four or five-wire systems
- Measurement of TRMS currents up to 6500Arms (sensor dependant)
- Measurement of DC current up to 1400ADC (with MR193 probe)
Fluke 435-II Power Quality & Energy Analyzer
- Quickly see how much money losing due to energy waste in terms of real dollars
- Easily see how motor startups are affecting motor drive performance
- Get at-a-glance power quality health data in real-time so you can make better maintenance decisions
Dranetz HDPQ Guide Power Quality Analyzer
- High definition PQ & energy monitoring: 1000 Vrms, AC/DC, 512 samples/cycle
- Eight channels, 4 voltage & 4 current
- AnswerModules: sag directivity, PF capacitor identification, motor: automatic event categorization
Dranetz HDPQ Guide SP Power Quality Analyzer
- IP65 enclosure
- GPS
- High Definition PQ & Energy Monitoring – 1000Vrms, AC/DC, 512 samples/cycle
Dranetz HDPQ Visa Power Quality & Energy Monitoring Analyzer
- High Definition PQ & Energy Monitoring – 1000Vrms, AC/DC, 512 samples/cycle
- Eight channels, 4 voltage & 4 current
- Advanced PQ – IEC 61000-4-30 Class A & IEEE 1159 compliant
Fluke 437-II Three-Phase Power Quality Analyzer
- Energy loss calculator: quantified to pinpoint true system energy losses in dollars
- Power inverter efficiency: simultaneously measure AC output power and DC input power for power electronics systems using optional DC clamp
- Capture fast RMS data, show half-cycle and waveforms to characterize electrical system dynamics
Dranetz HDPQ Xplorer Plus Power Quality Analyzer
- High Definition PQ & Energy Monitoring – 1000Vrms, AC/DC, 512 samples/cycle
- High Speed Digitized Transients – 1us, 10 to 2000Vpk
- Transient triggers – V & I – waveshape triggers, high speed. Well beyond PQ standards requirements
Fluke 1736 Three-Phase Power Logger
- Voltage range: 100 - 240V (standard)
- Power consumption: 50VA Max
- Frequency: 42.5 to 69Hz
Fluke 1775 Three-Phase Power Quality Analyzer
- Automatically measure power and power quality parameters
- At-a-glance power quality health for faster troubleshooting
- Easily view V/A/Hz, power, dips, swells, and harmonics data
Dranetz HDPQ Visa Plus
- Frequency | 16 - 25 Hz, 42.5 - 69 Hz, ±0.01 Hz
- Harmonics | IEC 61000-4-6, IEEE 519:2014
- Real power (W) | P: meets 0.2S requirements
Fluke 438-II Power Quality Analyzer & Motor Analyzer
- Measure key parameters on direct-on-line motors and motors driven by specific variable frequency drive systems including torque, RPM, mechanical power and motor efficiency
- Perform dynamic motor analysis by plotting of motor de-rating factor against load according to NEMA guidelines
- Calculate mechanical power and efficiency without the need of mechanical sensors, just connect to the input conductors and you’re ready to go
Fluke 1777 Three-Phase Power Quality Analyzer
- Voltage: 100V – 600V (-15% / +10%)
- Power Consumption: 40VA Max
- Bandwidth: DC to 30 kHz
Dranetz DranXperT
- DranXperT Power Logger with 4 Flex Current Probes 16-inch, 1500 A
- PQ disturbance/event detector, power/energy logger, and sensor logger
- 3 voltage channels – direct measurements up to 600 Vrms, CAT III
Fluke 1760 Three-Phase Power Quality Recorder Topas
- Fully Class-A compliant
- GPS time synchronization
- Flexible and fully configurable thresholds and scale factors
Fluke 1738 Advanced Power Logger
- Voltage range: 100 - 240V (standard)
- Power consumption: 50VA Max
- Bandwidth: 42.5Hz - 3.5kHz
Fluke 1664 FC Installation Multifunction Tester
- Multifunction tester that tests to all local regulations
- Includes "Insulation Pre-test" that detects when appliances are connected to the system and stops the test
- Runs seven installation tests automatically in one sequence with a single connection through Auto Test
AEMC PEL 103
- Simple to use, single-, dual- (split-phase) and three-phase (Y, ∆) power & energy loggers
- Provides all the necessary functions for Power and Energy data logging for 50Hz, 60Hz, 400Hz and DC distribution systems
- Current measurements from 200mA up to 10,000A using flexible current sensors
Fluke 43B 1-Phase Power Quality Analyzer | 600V/500A
- Displays voltage, current, and power waveforms
- Measures RMS, Peak, and Total Harmonic Distortion of voltage and current
- Displays harmonic detail in bar graph format
Fluke 1730 Three-Phase Electrical Energy Logger
- Key measurements: Voltage, current, power, power factor and associated values enable you to optimize and implement your energy saving strategies.
- Bright, color touch screen: Perform convenient in-the-field analysis and data checks with full graphical display.
- Comprehensive logging: More than 20 separate logging sessions can be stored on the instrument. In fact, all measured values are automatically logged and can be reviewed during logging and before
Fluke 430 Series Three-Phase Power Quality Analyzers
Hioki PW3198 Power Quality Analyzer
- Transient overvoltage : 2MHz sampling.
- Frequency cycle : Calculated as one cycle, 40 to 70Hz
- RMS voltage/ RMS current refreshed each half-cycle
AEMC 3945-B Three-phase PowerPad Power Quality Analyzer
- True RMS single, two, and three-phase measurements at 256 samples/cycle, plus DC
- Real-time color waveforms
- Easy-to-use on-screen setup