Additel 121 Pressure Manifolds
- Additel 121 is used for pneumatic pressure calibration up to 3000 psi (200bar)
- The unit goes with the Additel 780 Pressure Calibrator
- Filter is built into the manifold
Additel 123 Pressure Calibrator
- Additel 123 used for hydraulic pressure applications up to 15,000 psi (1,000 bar)
- Filter is built into the manifold
- Four hand-tight Quick Connectors
Fluke 1502A-156 Thermometer Readout
- Two Tweeners to choose from—reading PRTs or thermistors
- Accurately measures the resistance of the probe and then converts the resistance to a temperature value using its built-in algorithms
- Reads the common industrial grade IEC-751 or 385 ALPHA RTD without any programming
Fluke 154 Multifunction HART Communicator
- Full HART Device Description (DD) support of all HART devices
- Configure HART devices
- Perform HART trim on hart devices when used with a Fluke 750 or 720 series calibrator
Additel 221A Multifunction Temperature Calibrator
- Sourcing, simulating, and measuring temperature and electrical signals
- Smartphone-like menu and interface make the operation simpler and easier
- The internal cold junction compensation sensor can be re-calibrated at ice point by users
Additel 222A Multifunction Process Calibrator
- Sourcing, simulating and measuring pressure, temperature, and electrical signals
- Smartphone-like menu and interface make the operation simpler and easier
- The internal cold junction compensation sensor can be re-calibrated at ice point by users
Additel 223A Multifunction Process Calibrator
- Sourcing, simulating and measuring pressure, temperature, and electrical signals
- Smartphone-like menu and interface make the operation simpler
- Hart Communication capability
Additel 226 Multifunction Process Calibrator
- True RMS voltage meter capability
- Dual channel pressure module ports
- High static differential pressure measurement 0.002% FS
Additel 227 HART Communication Process Calibrator
- Easy-to-use cellphone-like interface
- High accuracy
- Thermocouple measurement performance
Fluke 2271A Industrial Pressure Calibrator
- Calibrate a wide range of gauges and sensors with a single instrument
- Two levels of accuracy, 0.01% reading or 0.02% FS
- Wide measurement range from -100 kPa to 20 MPa (-15 to 3000 psi)
Additel 227EX HART Communicator
- Intrinsically safe model
- Integrated with HART communication functions, permitting users to monitor, control, and calibrate HART instrumentations
- Sourcing, simulating and measuring pressure, temperature and electrical signals
Emerson HART Communicator 275 Hand-held Configurator / Calibrator
- Connect to any HART® instrument with the HART Communicator—the only communicator you’ll need.
- Store over 100 device configurations in just one HART Communicator— ready to carry to the field.
- Hook it up and turn it on— that’s how easy it is to use the HART Communicator.
Additel 282 Dual Channel Reference Thermometer Readout
- Accuracy to 0.006°C at 0°C
- Reference level accuracies
- Dual measurement channels
Additel 286 Multifunction Reference Thermometer Readout
- Measure and calibrate SPRTs, RTDs, thermistors, and thermocouples
- 1 PPM resistance ratio accuracy (channel 1)
- 8 1/2-digit DC multimeter
King Nutronics 3112 Pressure Calibration Test System
- Small size and light weight
- Rechargeable internal nitrogen supply
- Integral gauge cutout and relief valves
Fluke 3130 Portable Pneumatic Pressure Calibrator
- Measure and generate pressures from vacuum to 2 MPa (300 psi, 20 bar)
- Internal pump can generate vacuum to -80 kPa (-12 psi, -0.8 bar) or pressure to 2 MPa (300 psi, 20 bar)
- Supply pressure connection allowing the use of external gas supply up to 2 MPa (300 psi, 20 bar)
PIE Calibration 334 Loop Calibrator
- 4 - 20 mA loop calibrator
- Accurate to ±0.025% of Span at 4.00 & 20.00 EZ-CHECK outputs
- Separate compartment for no-tool battery changes with four inexpensive “AA” batteries
PIE Calibration 334Plus Electrical Calibrators
- Calibrate milliamp instruments and find hidden loop problems
- Accurate to ±0.025% of span at 4.00 & 20.00 EZ-CHECK outputs
- Automatic indication of loop current and leakage current
King Nutronics 3514 Portable Pressure Calibration System
- Test Fluid: Hydraulic oil
- Hand Pump Discharge Pressure: 0 to 10,000 psig
- Manifold Ports: Gauge (two)
King Nutronics 3604-A Thermo Unit
- High temperature (100 to 1,200°F)
- Unique dry well design and precision adapter chucks eliminate the need for messy thermal transfer oils.
- Excellent accuracy and temperature stability.
King Nutronics 3605-A Thermo Unit
- Dry well temperature calibration system
- Self-contained and portable
- IEEE-STD-488-1978 GPIB remote interface
King Nutronics 3657 Portable Calibration System
- Portable calibration system
- Vacuum pump case, hand pump case assembly, and more
- Ideal for precision calibration of several devices
Fluke Calibration 4180 Precision IR Calibrator
- Precision Infrared Calibrators for infrared thermometers and thermal imagers
- Fast, accurate, portable, and user-friendly
- Temperature range of –15°C to 120°C
Fluke 4181 Precision IR Temperature Calibrator
- Calibrated radiometrically for meaningful and consistent results
- Accredited calibration included
- Accurate, reliable performance from –15°C to 500°C
Fluke 4322 Automated Pressure Calibration System
- Controls and measures pressure from vacuum to 10,000 psi, with nominal accuracy of ± 0.1% of reading
- Lightweight, compact, rugged and transportable for in-situ calibration
- Integrated contamination prevention system enables direct calibration of pneumatic and hydraulic gauges without cleaning
Fluke 5560A High Performance Multi Product Calibrator
- Visual connetion managment terminals
- Isolated terminal block
- Touch screen display
Fluke 6102 Micro-Bath Thermometer Calibrator
- Small and portable with extreme stability
- Calibrates sensors of any size or shape
- Stability to ±0.015°C
Fluke 6109A / 7109A Portable Calibration Baths
- Calibrate up to four tri-clamp sanitary sensors at the same time
- Wide temperature ranges cover most process applications: 6109A: 35°C to 250°C 7109A: –25°C to 140°C
- 6109A: 35°C to 250°C
Fluke 6270A Pressure Controller/Calibrator
- Calibrate a wide range of gauges and sensors with a single instrument
- Modular configuration makes this a versatile and economical solution
- Easy to operate
Fluke 6330 Compact Temperature Calibration Bath
- Stability and uniformity each better than ±0.008°C
- Metrology-level performance in lab-friendly sizes
- Convenient use on benchtops or on matching carts
Additel 673 Digital Pressure Calibrator
- Pressure ranges up to 60,000 psi (4,200 bar)
- 0.02%, 0.05% FS or 0.1% RD accuracy
- Color touchscreen display
Fluke 702 Documenting Process Calibrator VDC/AC, mA, Ohms, TC & RTD
- Calibrate temperature, pressure, voltage, current, resistance, and frequency
- Simultaneously measure and source
- Automatically capture calibration results
Fluke 710 mA Loop Valve Tester
- 24 V DC loop power with mA measure mode (-25% to 125%)
- Resolution of 1 μA on mA ranges and 1 mV on voltages ranges
- Built in selectable 250 Ω resistor for HART communications
Fluke 7102 Micro-Bath Thermometer Calibrator
Fluke 712B RTD Temperature Calibrator
- Highly accurate, full-featured, and easy-to-use single function RTD temperature calibrator
- Measures and simulates 13 different RTD types and resistance
- Measures 4 to 20 mA signals while simultaneously sourcing a temperature signal
Fluke Calibration 714B Thermocouple/Temperature Calibrator
- Highly accurate, easy-to-use thermocouple temperature calibrator
- Measures and simulates 17 thermocouple types and millivolts
- Measures 4 to 20 mA signals while sourcing a temperature signal
Fluke 719Pro 150G Electric Pressure Calibrator
- 150 psi pressure ranges
- Pressure measurement from internal or external sensor
- Sourced/simulated or measured mA values
Fluke 719Pro 300G Electric Pressure Calibrator
- 300 psi pressure ranges
- Pressure measurement from internal or external sensor
- Sourced/simulated or measured mA values
Fluke 719Pro 30G Electric Pressure Calibrator
- Unique integrated electric pump for one handed pressure calibration
- Test pressure switches easily with easy-to-use switch test function
- Precision pressure adjust vernier for easy and accurate pressure calibration
Fluke 724 Temperature Calibrator
- A split-screen display. The upper display allows you to measure volts and current. The lower display allows you to measure and source volts, resistance temperature detectors, thermocouples, and ohms.
- A thermocouple (TC) input/output terminal and internal isothermal block with automatic reference junction temperature compensation.
- Measure RTDs, thermocouples, ohms, and volts to test sensors and transmitters
Fluke 725 Multifunction Process Calibrator
- Small and streamlined shape makes it easy to carry
- Rugged, reliable design stands up to field use
- Easy to read measure/source screen lets you view input and output simultaneously
Fluke 7250 Series Pressure Controller/Calibrators
- Pressure ranges from 0 to 5 and 0 to 3 000 psi (0 to 35 kPa and 0 to 21 MPa)
- Model 7250xi and 7250i provide advanced precision of 0.005% of reading
- Model 7250 provides 0.003% of full scale precision
Fluke 7250LP Low Pressure Calibrator
- 10 inH2O and 30 inH2O
- 20 inH2O and 60 inH2O
- 35 inH2O and 100 inH2O
Fluke 726 Precision Multifunction Process Calibrator
- More precise measurement and calibration source performance, accuracies of 0.01%.
- Two separate channels; measure, source and view process signals simultaneously
- Measure volts, mA, RTDs, thermocouples, frequency, and resistance to test sensors and transmitters
Fluke 729 Automatic Pressure Calibrator
- Automatic pressure generation and regulation to 300 psi
- Easily document the process using onboard test templates
- Automatic internal fine-pressure adjustment
Fluke 729 150G Automatic Pressure Calibrator
- Automatic pressure generation
- Easily document the process using onboard test templates
- Automatic internal fine-pressure adjustment
Fluke 729 150G FC Automatic Pressure Calibrator
- Automatic pressure generation
- Easily document the process using onboard test templates
- Automatic internal fine-pressure adjustment
Fluke 729 300G Automatic Pressure Calibrator
- Automatic pressure generation
- Easily document the process using onboard test templates
- Automatic internal fine-pressure adjustment
Fluke 729 300G FC Automatic Pressure Calibrator
- Automatic pressure generation
- Easily document the process using onboard test templates
- Automatic internal fine-pressure adjustment
Fluke 729 30G Automatic Pressure Calibrator
- Automatic pressure generation
- Easily document the process using onboard test templates
- Automatic internal fine-pressure adjustment
Fluke 729 30G FC Automatic Pressure Calibrator
- Automatic pressure generation
- Easily document the process using onboard test templates
- Automatic internal fine-pressure adjustment
Fluke 7320 Compact Temperature Calibration Bath
Fluke Calibration 7340-16 Deep-Well Compact Bath
- -40°C to 150°C
- Stability / uniformity to ±0.005°C
- 9.2L bath volume
Fluke 7381 Deep-Well Compact Bath
- ± 0.006°C at –80°C (ethanol)
- ± 0.005°C at 0°C (ethanol)
- ± 0.005°C at 100°C (oil 5012)
Fluke 741B Documenting Process Calibrator
- Measure volts, mA, RTDs, thermocouples, frequency, and ohms to test sensors, transmitters and other instruments
- Source/simulate volts, mA, thermocouples , RTDs, frequency, ohms, and pressure to calibrate transmitters
- Power transmitters during test using loop supply with simultaneous mA measurement
Fluke 743B Documenting Process Calibrator
- Measure volts, mA, RTDs, thermocouples, frequency, and ohms to test sensors, transmitters, and other instruments
- Source/simulate volts, mA, thermocouples, RTDs, frequency, ohms, and pressure to calibrate transmitters
- Power transmitters during test using loop supply with simultaneous mA measurement
Fluke 744 Documenting Process Calibrator (HART)
- Measure volts, mA, RTDs, thermocouples, frequency, and ohms to test sensors, transmitters and other instruments
- Source/simulate volts, mA, thermocouples, RTDs, frequency, ohms, and pressure to calibrate transmitters
- Power transmitters during test using loop supply with simultaneous mA measurement
Fluke 7526A Precision Process Calibrator
- Sources and measures DC voltage, current, resistance, RTDs, and thermocouples
- Measures pressure using Fluke 700 Pressure Modules
- Measures 4 - 20 mA loop current
Fluke 754 Documenting Process Calibrator-HART
- Measure volts, mA, RTDs, thermocouples, frequency, and ohms to test sensors, transmitters, and other instruments
- Source/simulate volts, mA, thermocouples, RTDs, frequency, ohms, and pressure to calibrate transmitters
- Power transmitters during test using loop supply with simultaneous mA measurement
Additel 760 Automatic Handheld Pressure Calibrator
- Fully automatic calibrator with built-in pump and controller
- Switchable internal pressure modules for expandable ranges
- Accuracy of 0.02%FS
Additel 761A-500/1K Automated Pressure Calibrator Series
- ADT761A-LLP
- ADT761A-500
- ADT761A-1K
Additel 762 Automated Hydraulic Pressure Calibrator
- Automated pressure generation and control to 10,000 psi (700 Bar)
- Accuracy to 0.01%FS
- Dual-range calibration
Additel 773 Pressure Controller/Generator
- Pressure ranges from -380 inH2O (-0.95 bar) to 400 inH2O (1 bar)
- Two removable internal pressure modules with multi-range selection
- Control stability of 0.003% FS
Additel 780 Pressure Calibrator
- Pressure ranges up to 1,000 psi or 3,000 psi (depending on model)
- Removable interchangeable intelligent sensors
- Precision accuracy models to 0.01% of reading
Additel 783 Pressure Controller
- Pressure ranges from -14.35 psi (-0.99 bar) to 3600 psi (250 bar)
- Two removable internal pressure modules with multi-range selection
- 0.02% FS, 0.01% FS, and 0.01% RD accuracy
Fluke 787 Process Meter
- DMM and a loop calibrator in one rugged, handheld tool
- Provides a precision 1000 V, 440 mA True-RMS digital multimeter designed to meet 1000 volt IEC 1010 CAT III standards
- Features a clear LCD with backlight; 4,000 counts (30,000 counts for DC current)
Fluke 789 Loop Calibration Multimeter
- 24 V Loop power supply
- Very large dual display
- Enhanced backlight with 2 brightness settings
Additel 793 Pressure Controller/Generator
- Maximum pressure control range to 15000 psi (1000 bar)
- Interchangeable pressure module
- Oil and water versions available
PIE Calibration 820 Multifunction Process Calibrator
- Automatic stepping and ramping
- Large display with backlight
- More thermocouple and RTD ranges with 0.1 degree resolution and better accuracy
PIE Calibration 820Elite Multifunction Diagnostic Calibrator
- Multifunction diagnostic process calibrator: mA, V, TC, ohms, RTD, Hz, pH, pressure
- Simulate pH probes into transmitters & analyzers
- Quickly diagnose ground fault and current leakage with patented loop diagnostic technology
PIE Calibration 820PM Multifunction Process Calibrators
- Calibrate milliamps and voltage
- Calibrate directly in temperature (°C & °F)
- Checkout flow and vibration systems
PIE Calibration 830 Diagnostic Process Calibrator
- Detect hidden loop problems with Patented Current leak detection technology
- Check all loop parameters at once with the LoopScope
- Automatically detect 2, 3, or 4 wire RTDs
PIE Calibration 830PM Multifunction Process Calibrators
- Calibrate milliamps and voltage
- Calibrate directly in temperature (°C & °F)
- Checkout flow and vibration systems
Additel 850-1200 Laboratory Thermocouple Calibration Furnace
- Temperature control from 300°C to 1200°C
- 3-in-1 furnace with 9 unique modes
- Stability of ±0.1°C
Additel 875 Dry Well Calibrator Series
- Four models ranging from -40°C to 660°C
- Portable, rugged, and quick to temperature
- Metrology-level performance in stability, uniformity, accuracy, and loading effect
Additel 878 Dry Well Calibrator Series
- Three models ranging from -40°C to 700°C
- Reference level performance in accuracy, stability, and uniformity
- Quick to temperature
Fluke 9009 Dual-Block Thermometer Calibrator
- Two independently controlled temperature blocks
- Temperatures from -15°C to 350°C in one unit
- Two wells in each block for simultaneous comparison calibrations
Fluke 9132 Portable Infrared Calibrator
- Rapid heating and cooling
- Hand strap
- RS-232 interface capability
Fluke 9142 Field Metrology Well
- Lightweight, portable, and fast
- Cool to –25 °C in 15 minutes and heat to 660°C in 15 minutes
- Built-in two-channel readout for PRT, RTD, thermocouple, 4-20 mA current
Fluke 9143 Field Metrology Well
- Lightweight, portable, and fast
- Cool to –25 °C in 15 minutes and heat to 660°C in 15 minutes
- Built-in two-channel readout for PRT, RTD, thermocouple, 4-20 mA current
Fluke 9144 Field Metrology Well
- Lightweight, portable, and fast
- Cool to -25°C in 15 minutes and heat to 660°C in 15 minutes
- Built-in two-channel readout for PRT, RTD, thermocouple, 4 - 20 mA current
Additel 917-N-Set Pneumatic Pressure Test Pump
- Portable, only 5.7 lb
- Great stability and high resolution
- Minimal maintenance
Fluke 9173-A-156 Field Metrology Well
- High-quality industrial heat sources (accuracy, stability, uniformity)
- Immersion depth to 203 mm (8 in)
- Optional ITS-90 reference input reads PRTs to ±0.006°C
Fluke 9190A Ultra-Cool Field Metrology Well
- Wide temperature range
- Excellent accuracy
- Best-in-class stability
Fluke Calibration 9260 Mini Fixed-Point Cell Furnace
- Easy-to-use fixed-point maintenance apparatus
- Cuts in half the financial investment required to do fixed-point calibrations
- Good introduction to fixed-point calibration
Isotech 970 PEGASUS R High Temperature IR Thermometer Calibrator
- 150°C to 1200°C
- Compact 20 mm diameter cavity
- Emissivity > 0.995 cavity 20 x 65 mm
Emerson TREXLFPKLWS3S AMS Trex Device Communicator
- Eliminate the need for specialized tools with power the loop functionality
- Quickly resolve field devices issues with advanced diagnostics
- Configure and test valves inline
AMETEK ASC-400 Multifunction Calibrator
- Large full color display
- Advanced Simplicity user interface
- Connection Assistant provides connection details for the current set-up
Yokogawa CA71 Handy CAL Calibrator
- Simultaneous signal generation and measurement capability
- AC voltage (including supply voltage) measurement capability
- A wide array of useful functions
Druck DPI 515 Precision Pressure Controller/Calibrator
- Pressure ranges up to 3000 psi
- Precision 0.01% full scale
- Measuremnt stability 0.01% of reading/year
Druck DPI 610HC Portable Hydraulic Pressure Calibrator
- Ranges -14.7 to 10,000 psi
- Accuracy from 0.025% full scale (FS)
- Integral combined pressure/vacuum pump
Druck DPI 610PC Pressure Calibrator
- Ease of use while meeting a wide range of application needs
- Portable
- Accuracy of ±0.025% full scale (FS)
Druck DPI 611 Hand-held Pressure Calibrator Series
- 50% smaller and 33% lighter than the DPI 610
- Generates 0 to 20 bar/300 psi in less than 30 seconds
- Creates 95% vacuum
Druck DPI 611-05G Hand-held Pressure Calibrator
- 50% smaller and 33% lighter than the DPI 610
- Creates 95% vacuum
- Pressure measurement is twice as accurate
Druck DPI 611-07G Hand-held Pressure Calibrator
- 50% smaller and 33% lighter than the DPI 610
- Creates 95% vacuum
- Pressure measurement is twice as accurate
Druck DPI 611-13G Hand-held Pressure Calibrator
- 50% smaller and 33% lighter than the DPI 610
- Creates 95% vacuum
- Pressure measurement is twice as accurate
Druck DPI 620 Modular Calibration & Hart Communication System
- Measure, source and simulate multiple parameters
- HART digital communicator
- Easy-to-use, with video quality touch screen, which can be operated by a gloved hand
Druck DPI 620 Genii Multifunction Calibrator with HART
- Multi-function capabilities, including electrical, frequency, temperature, and pressure
- Optional HART and Foundation Fieldbus communicators
- ATEX, IECEx and ETL approved for hazardous area use
Druck DPI 800 Pressure Indicator
- Ranges from 10 in H2O to 10,000 psi (25 mbar to 700 bar)
- Single or dual range configuration
- IDOS pressure sensors provide accuracies to 0.05% FS all-inclusive or 0.01% precision
Druck DPI 880 Multifunction Calibrator
- Multifunctional device
- Part of the Druck DPI 800 Series
- Uses Intelligent Digital Output Sensor (IDOS) technology
Druck DPI610E Pressure Calibrator Series
- 100,000 point data logging memory
- HART communication as standard on all versions
- Integral calibration record with calibration due countdown
Druck DPI 612 Pressure Calibrator
- The complete pressure calibration tool: pump, measure, analyze
- Fast and dependable from vacuum to 1000 bar/15000 psi
- Easy to use touch screen
Druck DPI 620 Genii-IS Multifunction Process Calibrators
- Multifunction capabilities, including electrical, frequency, temperature, and pressure
- Optional HART and Foundation Fieldbus communicators
- ATEX, IECEx and ETL approved for hazardous area use
Druck DPI 802 Pressure Calibrator
- Single or dual range configuration
- IDOS pressure sensors provide accuracies to 0.05% FS all-inclusive or 0.01% precision
- mA measure, switch test and 24V loop power
Fluke 725Ex Multifunction Process Calibrator
- Pressure switch test function to capture set, reset, and deadband values
- Small, streamlined shape, and rugged, reliable design that stands up to field use
- Simple, push-button user interface for easy operation
Omega FOB104 Fiber Optic Thermometer
- 0 - 10V
- 4 - 20mA (optional)
- 4 channels
Emerson HART Communicator 475
- Full-color graphical user interface
- Powerful field diagnostics
- Bluetooth® communication
Emerson HART Communicator 268
- Memory: Nonvolatile memory retains contents when unit is powered down, so long as the battery source is supplying power.
- Power Supply: Five AA 1.5 V batteries (rechargeable optional)
- Temperature Limits: Operating: 32 to 122 °F (0 to 50 °C) Storage Limits: -4 to 158 °F (-20 to 70 °C)
Emerson HART 375 Field Communicator
- Universal HART ® and Foundation™ fieldbus
- Intrinsically safe
- Rugged and reliable
Beamex MC5 Multifunction Fieldbus Calibrator
- Modular design allows configuration based on your needs
- Capabilities for pressure, temperature, electrical and frequency signals calibration
- Internal and/or external pressure modules
Beamex MC6 Field Process Calibrator
- Multi-functional field process calibrator and communicator in one device
- Fully paperless calibration process
- Unmatched accuracy
Fluke P5513 Pneumatic Comparison Test Pump
- High pressure pneumatic operation
- Screw press for fine pressure adjustments
- High quality needle valves for fine control
PCE Instruments PCE-789 Multifunction Calibrator
- Different signals simulation and measurement
- Integrated function generator
- Graphic display with backlight
PCE Instruments PCE-MCA 50 Process Calibrator
- Compact handset
- User friendly menu
- Rechargeable strong battery
PIE Calibration 541 Frequency Calibrator
- Frequency read & source functions
- Uses a standard 9V alkaline battery
- Calibrate totalizers
Druck PTC165 Premium TC Multifunction Calibrator
- Infrared calibration and surface calibration
- Ethernet, 3x USB interfaces
- Completely paperless calibration
King Nutronics Regulus 4200 Dual-Power Temperature Calibrator
- Customizable ramp-and-soak programing
- Automated switch testing
- Dual-axial well uniformity
AMETEK RTC-700 Reference Temperature Calibrator
- High accuracy
- Intuitive, fast, and user-friendly navigation
- Excellent stability
Isotech Saturn 877 Thermocouple Calibration Sphere
- Each thermocouple is completely isolated in a gas tight closed end tube
- Accuracy 0.25°C at 1000°C
- Central Zone of Zero Heat flux
Omega TRCIII Temperature Calibrator
- A 0°C (32°F) thermoelectric refrigerator
- Eliminates old-fashioned ice bath
- For versatile use in the factory, laboratory, and instrument shop
Omega TRCIII-A Temperature Reference Chamber
- Portable rugged case for use in the factory, calibration laboratory, or instrument shop
- Built-in temperature readout with 0.1 (°F/°C) resolution
- Accepts up to 6 probes at one time
Crystal XP2i Series Pressure Gauge
- Specified in percent of reading like deadweight testers
- Easy to read display, day or night
- 5 full digits, great for leak testing
Yokogawa YHC5150X Handheld HART Communicator
- Reads manufacturers' DDs in native format without the requirement for translations
- The HART-compliant modem communicates with any HART Device (registered or unregistered)
- Innovative ergonomic and handheld design